We may earn a referral commission from some links on this page. It doesn't change your price or our recommendations.
Thruster specs
Quick BTQ 185 DP: specs, price and the boats it fits
The BTQ 185 DP is Quick’s mid-size bow thruster with two propellers instead of one, for boats of about 26 to 50 ft. The second propeller gets more push out of the same size hole in the hull, about 143 to 231 lb on 12 or 24 V. Quick says no other maker offers twin propellers in this tube size. Beneteau fitted the model it replaced, the BTQ 180, on its Swift Trawler 34.
Prices start at $4,826 at Quick’s US store, for the thruster alone. You’ll also need a control panel ($540 for the joystick), the tube ($459) and a fuse with its holder. Plan on about $1,324 to $2,771 more for batteries, cable and a charger. See the cost table below.
Owners say it does the job, with two things worth knowing. One Swift Trawler 34 owner found his older twin-prop unit at the stern outmatched by strong wind on a tall boat. And the motor brushes wear over time, and Hanse owners have had theirs replaced. Quick says the thruster isn’t designed for continuous use, so its panel forces a 20 minute rest after about 5 minutes 40 seconds of running. The warranty is three years.
The full spec sheet for a yard sits lower down, and the Quick thruster review covers Quick’s whole range.
Where this summary comes from (11 sources, read 11 October 2026)
- Quick USA store product page
- Pressmare, 17 May 2023: Quick on contra-rotating propellers at 185 mm
- Boating Industry Canada, 18 May 2023: Quick thruster production began in 2007
- Quick BTQ Series installation manual, REV005A (July 2025)
- Quick TCD 2022/2042 control panel manual, REV001a
- Quick USA store: thrusters, panels, tubes, fuses and spares
- Quick USA: conditions of warranty
- YBW forums, Aug 2019: bow thruster opinions (Swift Trawler 34 owner)
- myHanse, Jul 2016: brushes, relay and a six-month parts wait
- myHanse, Aug 2016: thruster stops after hard use in a crosswind
- myHanse, Jun 2022: Quick stern thruster, brushes and the overheat lockout
Choose a size
The Quick BTQ 185 DP comes in three sizes. Each has its own price, wiring and boats it suits, so pick one and the facts, the fit, the cost and the spec sheet below show that size.
| Size | Push | Voltage | Quick’s boat length | Price |
|---|---|---|---|---|
| BTQ 185-65 | 143 lb (65 kgf) | 12 or 24 V | 26 to 39 ft | $4,201 to $4,826 |
| BTQ 185-85 | 187 lb (85 kgf) | 12 or 24 V | 33 to 50 ft | $4,924 to $5,369 |
| BTQ 185-105 | 231 lb (105 kgf) | 12 or 24 V | 39 to 50 ft | $8,752 |
Key facts
- DIY level 1 of 5 Yard job
- Thrust 143 lb 65 kgf, Quick's rating
- Boat length 26 to 39 ft Quick's own range
- Price $4,201 to $4,826 equipment only, quickusastore.com, 12 October 2026
- Fitted by a yard $11,806 to $15,252 Our estimate at 35 ft, unit and job
- Voltage 12 V or 24 V As sold
- Mounts Tunnel Fixed mount, bow
- To fit it Haul-out The boat comes out of the water
- Run limit Not published Quick prints none for the motor. Its control panel cuts the command after about five minutes
Every figure here is the maker’s or a dealer’s, except the fitted cost, which is our estimate. The full spec sheet is further down.
How much of the install is yours
DIY levels
- Level 5: Owner install. No yard, no electrician.
- Level 4: You fit it, electrician connects. You mount and wire it; a marine electrician makes the final connections.
- Level 3: Split with the yard. The yard does the below-waterline part; you do the wiring.
- Level 2: Wiring prep only. The yard fits the unit and does the hull work; you do the wiring prep.
- Level 1: Yard job. A qualified professional does all of it.
You Yard Electrician. The bar is labor hours; a haul-out is a note.
How we rate DIYYou: none Yard: 32 to 70 h Electrician: in the yard’s hours Plus a haul-out.
- The whole job: hull, unit and wiring Yard 32 to 70 h The low end is two crew over two days, the job as owners describe it on the forums. The high end rises with boat length between two real billed figures: 32 hours at 35 ft, and the largest invoice we hold, 70 hours at 47 ft.
Quick’s manual: “Installation and subsequent inspection or repair work must only be carried out by qualified personnel.” The manual.
Hours are labor only.
Is it right for your boat?
Our figure is the longest boat one unit can steer in a 15 knot wind. It is a range because each kind of boat catches the wind differently. Here a houseboat gets full thrust to 30 ft, and a catamaran to 42 ft. The maker gives one range for every boat.
The table below tries the Quick BTQ 185 DP on each kind of boat, at every length that kind of boat is built in. The wind is 15 knots and the rules are the finder’s own. A length counts as a fit when the unit gives the thrust that boat needs at the bow and the maker lists it for that length.
A boat up to 10 percent past the maker’s range still counts here, as it does in the finder. So the table runs up to 42 ft, just past Quick’s own range (26 to 39 ft).
| Boat | Full thrust at 15 knots | Still a fit, in lighter wind |
|---|---|---|
| Pontoon & tritoon | Not listed. A pontoon has no hull body between the logs to bore a tunnel through, and nobody sells one for these boats. | |
| Sailboat | 34 to 40 ft | 41 to 42 ftfull thrust to about 14 knots at 42 ft |
| Houseboat | 30 ft only | 31 to 42 ftfull thrust to about 11 knots at 42 ft |
| Catamaran | 39 to 42 ft | None |
| Trawler | 34 to 40 ft | 41 to 42 ftfull thrust to about 14 knots at 42 ft |
| Motor yacht | 35 to 40 ft | 41 to 42 ftfull thrust to about 14 knots at 42 ft |
| Bass & flats | Not listed. Nobody sells a tunnel kit for these hulls, and a bass boat’s shallow planing bow has almost no depth to hold one. | |
| Wake & ski boats | Not listed. Nobody sells a tunnel kit for these hulls. | |
| Express cruiser | No length. More thrust than the boat needs. | |
| Center console | No length. More thrust than the boat needs. | |
Reading the two length columns. The first column is where one unit gives all the thrust the boat needs in 15 knots. The second is where the finder still lists it: the unit falls short of what the boat needs by no more than 10 percent, and gives the whole figure only in the lighter wind named. On a boat shorter than the first column’s shortest length, the unit is more than the boat needs.
It is sized for five kinds of boat here. For your own boat, the finder gives an answer that also counts your drive and who does the fitting. The compare page sets this unit beside others.
What it costs fitted
These totals are our estimate of a yard job: the unit’s price, plus a yard’s hours at $160 to $180 an hour, plus the batteries, cable and charger, plus the other parts the box does not hold. A Lifting the boat out of the water on a travel lift or a trailer so work can be done below the waterline. It is billed separately from the job itself. adds $540 to $2,030 at these lengths, with 5 to 7 days out of the water, worked from eight yards’ own rate cards. The hours come from what owners and yards report. Your own yard will have its own opinion. The cost page builds the same figures line by line.
| Boat length | The unit | Yard labor | Haul-out | Batteries, cable, charger | Other parts | Total |
|---|---|---|---|---|---|---|
| 30 ft | $4,201 to $4,826 | $5,120 to $5,760about 32 hours | $540 to $1,450 | $1,324 to $1,607 | $541 to $1,369 | $11,726 to $15,012 |
| 35 ft | $4,201 to $4,826 | $5,120 to $5,760about 32 hours | $620 to $1,690 | $1,324 to $1,607 | $541 to $1,369 | $11,806 to $15,252 |
| 42 ft | $4,201 to $4,826 | $5,120 to $9,72032 to 54 hours | $750 to $2,030 | $1,324 to $1,607 | $541 to $1,369 | $11,936 to $19,552 |
How the batteries, cable and charger add up. We price a battery bank close to the thruster, as the makers recommend, with 10 to 20 ft of cable out and back: red for the positive, black for the negative, cut to length. The low end is the cheapest battery that meets the figure and the shorter run; the high end is a sealed (AGM) battery and the longer run. The charger is a NOCO GEN5X2 two-bank shore charger.
Batteries and lugs are priced at Fisheries Supply and the cable and charger at Defender, read 12 October 2026.
- At 12 V: one 12 V battery, at least 550 CCA and 120 Ah (Quick’s minimum), $998 for the battery; Quick’s cable table gives 3/0 to 2 x 1/0 AWG, priced on 4/0 AWG, the nearest size cut to length: $180 to $314 for the red and black cable and the lugs; a GEN5X2 charger, $146.
- At 24 V: two 12 V batteries in series, at least 450 CCA and 80 Ah each (Quick’s minimum), $1,147 for both; Quick’s cable table gives 1/0 to 3/0 AWG, priced on 1/0 to 4/0 AWG, the nearest size cut to length: $95 to $314 for the red and black cable and the lugs; a GEN5X2 charger, $146.
The sizing and the costs on this page are estimates, for guidance only and without warranty. They are no quote, and nobody has inspected your boat. Check them against the maker’s manual and your yard before you rely on them. Terms of use.
Key facts
- DIY level 1 of 5 Yard job
- Thrust 187 lb 85 kgf, Quick's rating. The listing prints 165.3 lb
- Boat length 33 to 50 ft Quick's own range
- Price $4,924 to $5,369 equipment only, quickusastore.com, 12 October 2026
- Fitted by a yard $12,709 to $22,884 Our estimate at 45 ft, unit and job
- Voltage 12 V or 24 V As sold
- Mounts Tunnel Fixed mount, bow
- To fit it Haul-out The boat comes out of the water
- Run limit Not published Quick prints none for the motor. Its control panel cuts the command after about five minutes
Every figure here is the maker’s or a dealer’s, except the fitted cost, which is our estimate. The full spec sheet is further down.
How much of the install is yours
DIY levels
- Level 5: Owner install. No yard, no electrician.
- Level 4: You fit it, electrician connects. You mount and wire it; a marine electrician makes the final connections.
- Level 3: Split with the yard. The yard does the below-waterline part; you do the wiring.
- Level 2: Wiring prep only. The yard fits the unit and does the hull work; you do the wiring prep.
- Level 1: Yard job. A qualified professional does all of it.
You Yard Electrician. The bar is labor hours; a haul-out is a note.
How we rate DIYYou: none Yard: 32 to 70 h Electrician: in the yard’s hours Plus a haul-out.
- The whole job: hull, unit and wiring Yard 32 to 70 h The low end is two crew over two days, the job as owners describe it on the forums. The high end rises with boat length between two real billed figures: 32 hours at 35 ft, and the largest invoice we hold, 70 hours at 47 ft.
Quick’s manual: “Installation and subsequent inspection or repair work must only be carried out by qualified personnel.” The manual.
Hours are labor only.
Is it right for your boat?
Our figure is the longest boat one unit can steer in a 15 knot wind. It is a range because each kind of boat catches the wind differently. Here a houseboat gets full thrust to 34 ft, and an express cruiser to 55 ft. The maker gives one range for every boat.
The table below tries the Quick BTQ 185 DP on each kind of boat, at every length that kind of boat is built in. The wind is 15 knots and the rules are the finder’s own. A length counts as a fit when the unit gives the thrust that boat needs at the bow and the maker lists it for that length.
A boat up to 10 percent past the maker’s range still counts here, as it does in the finder. So the table runs down to 30 ft and up to 55 ft, just past Quick’s own range (33 to 50 ft).
| Boat | Full thrust at 15 knots | Still a fit, in lighter wind |
|---|---|---|
| Pontoon & tritoon | Not listed. A pontoon has no hull body between the logs to bore a tunnel through, and nobody sells one for these boats. | |
| Sailboat | 38 to 46 ft | 47 to 55 ftfull thrust to about 13 knots at 55 ft |
| Houseboat | 30 to 34 ft | 35 to 51 ftfull thrust to about 10 knots at 51 ft |
| Catamaran | 43 to 52 ft | 53 to 55 ftfull thrust to about 14 knots at 55 ft |
| Trawler | 38 to 45 ft | 46 to 55 ftfull thrust to about 12 knots at 55 ft |
| Motor yacht | 38 to 45 ft | 46 to 55 ftfull thrust to about 12 knots at 55 ft |
| Bass & flats | Not listed. Nobody sells a tunnel kit for these hulls, and a bass boat’s shallow planing bow has almost no depth to hold one. | |
| Wake & ski boats | Not listed. Nobody sells a tunnel kit for these hulls. | |
| Express cruiser | 48 to 55 ft | None |
| Center console | No length. More thrust than the boat needs. | |
Reading the two length columns. The first column is where one unit gives all the thrust the boat needs in 15 knots. The second is where the finder still lists it: the unit falls short of what the boat needs by no more than 10 percent, and gives the whole figure only in the lighter wind named. On a boat shorter than the first column’s shortest length, the unit is more than the boat needs.
It is sized for six kinds of boat here. For your own boat, the finder gives an answer that also counts your drive and who does the fitting. The compare page sets this unit beside others.
What it costs fitted
These totals are our estimate of a yard job: the unit’s price, plus a yard’s hours at $160 to $180 an hour, plus the batteries, cable and charger, plus the other parts the box does not hold. A Lifting the boat out of the water on a travel lift or a trailer so work can be done below the waterline. It is billed separately from the job itself. adds $540 to $2,650 at these lengths, with 5 to 7 days out of the water, worked from eight yards’ own rate cards. The hours come from what owners and yards report. Your own yard will have its own opinion. The cost page builds the same figures line by line.
| Boat length | The unit | Yard labor | Haul-out | Batteries, cable, charger | Other parts | Total |
|---|---|---|---|---|---|---|
| 30 ft | $4,924 to $5,369 | $5,120 to $5,760about 32 hours | $540 to $1,450 | $1,324 to $2,456 | $541 to $1,369 | $12,449 to $16,404 |
| 45 ft | $4,924 to $5,369 | $5,120 to $11,52032 to 64 hours | $800 to $2,170 | $1,324 to $2,456 | $541 to $1,369 | $12,709 to $22,884 |
| 55 ft | $4,924 to $5,369 | $5,120 to $12,60032 to 70 hours | $1,080 to $2,650 | $1,324 to $2,456 | $541 to $1,369 | $12,989 to $24,444 |
How the batteries, cable and charger add up. We price a battery bank close to the thruster, as the makers recommend, with 10 to 20 ft of cable out and back: red for the positive, black for the negative, cut to length. The low end is the cheapest battery that meets the figure and the shorter run; the high end is a sealed (AGM) battery and the longer run. The charger is a NOCO GEN5X2 two-bank shore charger.
Batteries and lugs are priced at Fisheries Supply and the cable and charger at Defender, read 12 October 2026.
- At 12 V: one 12 V battery, at least 1,000 CCA and 200 Ah (Quick’s minimum), $998 for the battery; Quick’s cable table gives 2 x 1/0 to 2 x 3/0 AWG, priced on 4/0 to 2 x 4/0 AWG, the nearest size cut to length: $180 to $629 for the red and black cable and the lugs; a GEN5X2 charger, $146.
- At 24 V: two 12 V batteries in series, at least 800 CCA and 150 Ah each (Quick’s minimum), $1,996 for both; Quick’s cable table gives 3/0 to 2 x 1/0 AWG, priced on 4/0 AWG, the nearest size cut to length: $180 to $314 for the red and black cable and the lugs; a GEN5X2 charger, $146.
The sizing and the costs on this page are estimates, for guidance only and without warranty. They are no quote, and nobody has inspected your boat. Check them against the maker’s manual and your yard before you rely on them. Terms of use.
Key facts
- DIY level 1 of 5 Yard job
- Thrust 231 lb 105 kgf, Quick's rating. The listing prints 209.5 lb
- Boat length 39 to 50 ft Quick's own range
- Price $8,752 equipment only, quickusastore.com, 12 October 2026
- Fitted by a yard $17,535 to $26,582 Our estimate at 45 ft, unit and job
- Voltage 12 V or 24 V As sold
- Mounts Tunnel Fixed mount, bow
- To fit it Haul-out The boat comes out of the water
- Run limit Not published Quick prints none for the motor. Its control panel cuts the command after about five minutes
Every figure here is the maker’s or a dealer’s, except the fitted cost, which is our estimate. The full spec sheet is further down.
How much of the install is yours
DIY levels
- Level 5: Owner install. No yard, no electrician.
- Level 4: You fit it, electrician connects. You mount and wire it; a marine electrician makes the final connections.
- Level 3: Split with the yard. The yard does the below-waterline part; you do the wiring.
- Level 2: Wiring prep only. The yard fits the unit and does the hull work; you do the wiring prep.
- Level 1: Yard job. A qualified professional does all of it.
You Yard Electrician. The bar is labor hours; a haul-out is a note.
How we rate DIYYou: none Yard: 32 to 70 h Electrician: in the yard’s hours Plus a haul-out.
- The whole job: hull, unit and wiring Yard 32 to 70 h The low end is two crew over two days, the job as owners describe it on the forums. The high end rises with boat length between two real billed figures: 32 hours at 35 ft, and the largest invoice we hold, 70 hours at 47 ft.
Quick’s manual: “Installation and subsequent inspection or repair work must only be carried out by qualified personnel.” The manual.
Hours are labor only.
Is it right for your boat?
Our figure is the longest boat one unit can steer in a 15 knot wind. It is a range because each kind of boat catches the wind differently. Here a houseboat gets full thrust to 38 ft, and a catamaran to 55 ft. The maker gives one range for every boat.
The table below tries the Quick BTQ 185 DP on each kind of boat, at every length that kind of boat is built in. The wind is 15 knots and the rules are the finder’s own. A length counts as a fit when the unit gives the thrust that boat needs at the bow and the maker lists it for that length.
A boat up to 10 percent past the maker’s range still counts here, as it does in the finder. So the table runs down to 36 ft and up to 55 ft, just past Quick’s own range (39 to 50 ft).
| Boat | Full thrust at 15 knots | Still a fit, in lighter wind |
|---|---|---|
| Pontoon & tritoon | Not listed. A pontoon has no hull body between the logs to bore a tunnel through, and nobody sells one for these boats. | |
| Sailboat | 42 to 51 ft | 52 to 55 ftfull thrust to about 14 knots at 55 ft |
| Houseboat | 36 to 38 ft | 39 to 55 ftfull thrust to about 10 knots at 55 ft |
| Catamaran | 48 to 55 ft | None |
| Trawler | 42 to 51 ft | 52 to 55 ftfull thrust to about 14 knots at 55 ft |
| Motor yacht | 42 to 51 ft | 52 to 55 ftfull thrust to about 14 knots at 55 ft |
| Bass & flats | Not listed. Nobody sells a tunnel kit for these hulls, and a bass boat’s shallow planing bow has almost no depth to hold one. | |
| Wake & ski boats | Not listed. Nobody sells a tunnel kit for these hulls. | |
| Express cruiser | 53 to 55 ft | None |
| Center console | No length. More thrust than the boat needs. | |
Reading the two length columns. The first column is where one unit gives all the thrust the boat needs in 15 knots. The second is where the finder still lists it: the unit falls short of what the boat needs by no more than 10 percent, and gives the whole figure only in the lighter wind named. On a boat shorter than the first column’s shortest length, the unit is more than the boat needs.
It is sized for six kinds of boat here. For your own boat, the finder gives an answer that also counts your drive and who does the fitting. The compare page sets this unit beside others.
What it costs fitted
These totals are our estimate of a yard job: the unit’s price, plus a yard’s hours at $160 to $180 an hour, plus the batteries, cable and charger, plus the other parts the box does not hold. A Lifting the boat out of the water on a travel lift or a trailer so work can be done below the waterline. It is billed separately from the job itself. adds $640 to $2,650 at these lengths, with 5 to 7 days out of the water, worked from eight yards’ own rate cards. The hours come from what owners and yards report. Your own yard will have its own opinion. The cost page builds the same figures line by line.
| Boat length | The unit | Yard labor | Haul-out | Batteries, cable, charger | Other parts | Total |
|---|---|---|---|---|---|---|
| 36 ft | $8,752 | $5,120 to $6,30032 to 35 hours | $640 to $1,740 | $2,322 to $2,771 | $541 to $1,369 | $17,375 to $20,932 |
| 45 ft | $8,752 | $5,120 to $11,52032 to 64 hours | $800 to $2,170 | $2,322 to $2,771 | $541 to $1,369 | $17,535 to $26,582 |
| 55 ft | $8,752 | $5,120 to $12,60032 to 70 hours | $1,080 to $2,650 | $2,322 to $2,771 | $541 to $1,369 | $17,815 to $28,142 |
How the batteries, cable and charger add up. We price a battery bank close to the thruster, as the makers recommend, with 10 to 20 ft of cable out and back: red for the positive, black for the negative, cut to length. The low end is the cheapest battery that meets the figure and the shorter run; the high end is a sealed (AGM) battery and the longer run. The charger is a NOCO GEN5X2 two-bank shore charger.
Batteries and lugs are priced at Fisheries Supply and the cable and charger at Defender, read 12 October 2026.
- At 12 V: two 12 V batteries side by side (in parallel), at least 550 CCA and 125 Ah each (Quick’s minimum), $1,996 for both; Quick’s cable table gives 2 x 3/0 to 2 x 4/0 AWG, priced on 2 x 4/0 AWG, the nearest size cut to length: $360 to $629 for the red and black cable and the lugs; a GEN5X2 charger, $146.
- At 24 V: two 12 V batteries in series, at least 800 CCA and 150 Ah each (Quick’s minimum), $1,996 for both; Quick’s cable table gives 3/0 to 2 x 1/0 AWG, priced on 4/0 AWG, the nearest size cut to length: $180 to $314 for the red and black cable and the lugs; a GEN5X2 charger, $146.
The sizing and the costs on this page are estimates, for guidance only and without warranty. They are no quote, and nobody has inspected your boat. Check them against the maker’s manual and your yard before you rely on them. Terms of use.
What else you buy
What follows comes from Quick’s BTQ Series installation manual REV 005A and the TCD control manual, September 2025, read 30 September 2026.
- In the box
- The thruster with its reversing contactor and anode, a drilling template, gasket, O-ring, the manual.
- Bought separately
- "Recommended Quick accessories not included": the TCD control panels, the line switch, the THF fuse holder. Plus the fuse, the cable, a battery disconnection switch, a 4 A control fuse and switch, the tube.
- Charging
- The manual gives a battery table by model, in amp-hours and cold cranking amps, and a diagram with the panel on the service battery. It says nothing about how the thruster bank is charged.
The manual’s words, page 10: “Standard supply and material included in the package: Thruster, Drilling template, Gasket, O-ring, Installation and use manual, Conditions of warranty.”
The “other parts” line in the estimate above is the priced parts below, $541 to $1,369 at Fisheries Supply’s prices on 30 September 2026. The batteries, cable and charger have a line of their own.
| Part | What it is | What to ask for | Dealer price |
|---|---|---|---|
| Tunnel tube | The fiberglass, aluminum or steel pipe the thruster sits in, bonded through the bow. | Quick names none | $205–$554185 mm fiberglass tunnel tubes up to 60 in (1.5 m) long (VETUS, Sleipner Side-Power, Lewmar), at Fisheries Supply, read 16 October 2026. |
| Control panel | The buttons or joystick at the helm. One helm, one panel: a second steering station needs a panel of its own. | TCD 2022, 2042, 2044 or 2062 | $219–$374Side-Power touch panel and single joystick, VETUS push-button panel, Lewmar single joystick, at Fisheries Supply. |
| Control cable, panel to motor | The thin cable from the helm to the motor. Sold by length. | Quick names none | $29–$173Side-Power control cables, VETUS panel cables, Lewmar Gen 2 connecting cables, at Fisheries Supply. |
| Main fuse | A slow-blow fuse of the ANL type at the battery, in the size the maker prints for the model. | CNL DIN fuse, the rating in the manual | $18–$57Side-Power ANL fuses, Blue Sea ANL fuses, at Fisheries Supply, read 16 October 2026. |
| Fuse holder | The block the ANL fuse bolts into, with a cover. | THF3 to THF6 | $27–$93Egis and Blue Sea ANL fuse blocks, Side-Power ANL fuse holders, at Fisheries Supply, read 16 October 2026. |
| Main battery switch | The switch that cuts the thruster off from its battery when you leave the boat. | TSC 2000 or TMS line switch, or a battery switch | $35–$107Egis m-Series 300 A, Blue Sea e-Series 350 A and HD-Series 600 A on/off switches, at Fisheries Supply, read 16 October 2026. |
| Control-circuit fuse and switch | A small fuse, and often a switch, on the thin wire that powers the panel or control box. | A 4 A fast-blow fuse and a switch | $8–$12Blue Sea in-line ATO fuse holders, at Fisheries Supply, read 16 October 2026. |
| Battery cable and lugs | The two heavy cables from the battery to the motor, sized to the length of the run. The wiring calculator sizes them. | Quick names none | In the electrical line |
| Battery bank | A cranking-type bank near the motor, sized by the maker's cold cranking amps. The battery calculator checks it. | Quick names none | In the electrical line |
| Charger or charge feed | How the thruster bank gets charged: a shore charger of its own, a DC-to-DC charger or charging relay from the boat's system, or a charger built into the unit. | Quick names none | $146–$305NOCO GEN5X2 shore charger, Victron Orion-Tr Smart DC-DC charger, Blue Sea ML-ACR charging relay, at Fisheries Supply. |
| Glass, resin, filler and sealant | What bonds the tube or housing into the hull and seals the gear leg. | Quick names none | Not priced |
The cost page has the whole list with what every maker says about each part.
For the yard and the installer
The full spec sheet, grouped the way a yard reads it. Every figure is the maker’s or a dealer’s, with its source.
| Thrust and motor | |
|---|---|
| Thrust | 143 lb (65 kgf) As printed: 65 Kgf (143.3 lb) |
| Motor | 3.3 kW |
| Voltage | 12 V or 24 V |
| Fitting | |
| Type | Tunnel, fixed mount |
| End of the boat | Bow |
| Tunnel diameter | 185 mm |
| What it does to the hull | Tunnel bore below the waterline |
| Haul-out to fit it | Yes |
| Maker’s boat length | 26 to 39 ft |
| The tunnel | |
| Tunnel length | The optimal length is three to four times the tube diameter. A ratio of up to six can be tolerated. Longer tubes lose more of the thrust to friction. Quick’s installation manual |
| Depth below the waterline | In the bow and as low as possible, at least 0.75 times the tunnel diameter below the waterline, to avoid cavitation at the propeller. BTQ250 and BTQ300 installation manual, REV006C |
| Price and ordering | |
| Price | $4,201 to $4,826 equipment only, the maker's own price, quickusastore.com, 12 October 2026 |
| Part number | FGBT18065120T00BTQ 185-65, 65 KGF, double propeller, 12 V FGBT18065240T00BTQ 185-65, 65 KGF, double propeller, 24 V FGBT18085120T00BTQ 185-85, 85 KGF, double propeller, 12 V FGBT18085240T00BTQ 185-85, 85 KGF, double propeller, 24 V FGBT18105120T00BTQ 185-105, 105 KGF, double propeller, 12 V FGBT18105240T00BTQ 185-105, 105 KGF, double propeller, 24 V |
| Documents | |
| Manual | Installation manual (PDF)on the maker's site |
| Warranty | Quick gives at least 3 years from purchase, with repair or replacement at Quick's discretion. It is void if maintenance is done by anyone Quick has not authorized, or with parts that are not original. Removal and refitting are at your cost. Quick USA's conditions of warranty |
| The site’s review | Quick thruster review |
For the yard and the installer
The full spec sheet, grouped the way a yard reads it. Every figure is the maker’s or a dealer’s, with its source.
| Thrust and motor | |
|---|---|
| Thrust | 187 lb (85 kgf) As printed: 85 Kgf (165.3 lb) |
| Motor | 4.3 kW |
| Voltage | 12 V or 24 V |
| Fitting | |
| Type | Tunnel, fixed mount |
| End of the boat | Bow |
| Tunnel diameter | 185 mm |
| What it does to the hull | Tunnel bore below the waterline |
| Haul-out to fit it | Yes |
| Maker’s boat length | 33 to 50 ft |
| The tunnel | |
| Tunnel length | The optimal length is three to four times the tube diameter. A ratio of up to six can be tolerated. Longer tubes lose more of the thrust to friction. Quick’s installation manual |
| Depth below the waterline | In the bow and as low as possible, at least 0.75 times the tunnel diameter below the waterline, to avoid cavitation at the propeller. BTQ250 and BTQ300 installation manual, REV006C |
| Price and ordering | |
| Price | $4,924 to $5,369 equipment only, the maker's own price, quickusastore.com, 12 October 2026 |
| Part number | FGBT18065120T00BTQ 185-65, 65 KGF, double propeller, 12 V FGBT18065240T00BTQ 185-65, 65 KGF, double propeller, 24 V FGBT18085120T00BTQ 185-85, 85 KGF, double propeller, 12 V FGBT18085240T00BTQ 185-85, 85 KGF, double propeller, 24 V FGBT18105120T00BTQ 185-105, 105 KGF, double propeller, 12 V FGBT18105240T00BTQ 185-105, 105 KGF, double propeller, 24 V |
| Documents | |
| Manual | Installation manual (PDF)on the maker's site |
| Warranty | Quick gives at least 3 years from purchase, with repair or replacement at Quick's discretion. It is void if maintenance is done by anyone Quick has not authorized, or with parts that are not original. Removal and refitting are at your cost. Quick USA's conditions of warranty |
| The site’s review | Quick thruster review |
For the yard and the installer
The full spec sheet, grouped the way a yard reads it. Every figure is the maker’s or a dealer’s, with its source.
| Thrust and motor | |
|---|---|
| Thrust | 231 lb (105 kgf) As printed: 105 Kgf (209.5 lb) |
| Motor | 6.3 kW |
| Voltage | 12 V or 24 V |
| Fitting | |
| Type | Tunnel, fixed mount |
| End of the boat | Bow |
| Tunnel diameter | 185 mm |
| What it does to the hull | Tunnel bore below the waterline |
| Haul-out to fit it | Yes |
| Maker’s boat length | 39 to 50 ft |
| The tunnel | |
| Tunnel length | The optimal length is three to four times the tube diameter. A ratio of up to six can be tolerated. Longer tubes lose more of the thrust to friction. Quick’s installation manual |
| Depth below the waterline | In the bow and as low as possible, at least 0.75 times the tunnel diameter below the waterline, to avoid cavitation at the propeller. BTQ250 and BTQ300 installation manual, REV006C |
| Price and ordering | |
| Price | $8,752 equipment only, the maker's own price, quickusastore.com, 12 October 2026 |
| Part number | FGBT18065120T00BTQ 185-65, 65 KGF, double propeller, 12 V FGBT18065240T00BTQ 185-65, 65 KGF, double propeller, 24 V FGBT18085120T00BTQ 185-85, 85 KGF, double propeller, 12 V FGBT18085240T00BTQ 185-85, 85 KGF, double propeller, 24 V FGBT18105120T00BTQ 185-105, 105 KGF, double propeller, 12 V FGBT18105240T00BTQ 185-105, 105 KGF, double propeller, 24 V |
| Documents | |
| Manual | Installation manual (PDF)on the maker's site |
| Warranty | Quick gives at least 3 years from purchase, with repair or replacement at Quick's discretion. It is void if maintenance is done by anyone Quick has not authorized, or with parts that are not original. Removal and refitting are at your cost. Quick USA's conditions of warranty |
| The site’s review | Quick thruster review |
What holds up and what to weigh
Each point names the fact it rests on.
What holds up
- It is sold at 12 V and at 24 V.The maker's and dealers' listings
What to weigh
- The boat comes out of the water to fit it: it needs a tunnel bore below the waterline.The mounting: a bore through the hull, or a housing recessed into it
What the manual and listings say
This is the note we keep on the Quick BTQ 185 DP, written from the maker’s manual, its product pages and the dealer’s listing.
In the box: The thruster, a drilling template, gasket and O-ring. The TCD panel and the fuse holder are bought.
BTQ 185-65, 65 KGF, double propeller, 12 V
Twin counter-rotating propellers in the same 185 mm tunnel as the single-propeller BTQ 185. The 65 kgf version. The manual prints its thrust as "65 kgf (55.1 lb)", the 25 kgf unit's pounds. The manual gives a 275 A fuse at 12 V and a weight of 17.6 kg.
Its cable is 2/0 for a total run under 5 m (positive plus negative), two 1 AWG per leg to 10 m, two 2/0 AWG per leg to 20 m. At 24 V the fuse is 175 A and the cable 1 AWG, 2/0 and 3/0 by band. The manual prints a fuse and cable sizes but no current draw and no battery figure.
No product page gives a run time. The installation manual says the unit is not designed for continuous use and leaves the limit to the control panel. The panel's own manual cuts the command after about five minutes and resets it after a cool-down the panel computes. The warranty runs three years from purchase, with repair or replacement at Quick's discretion.
The warranty is void for maintenance by anyone Quick has not authorized or for non-original parts. Removal and refitting are at your cost. The price is Quick's US store's own for this size at 12 V, read 12 October.
BTQ 185-65, 65 KGF, double propeller, 24 V
The price is Quick's US store's own for this size at 24 V, read 12 October.
BTQ 185-85, 85 KGF, double propeller, 12 V
The 85 kgf version. The manual gives a 400 A fuse at 12 V and a weight of 17.9 kg. Its cable is two 1 AWG per leg for a total run under 5 m (positive plus negative), two 2/0 AWG per leg to 10 m, two 3/0 AWG per leg to 20 m. At 24 V the fuse is 275 A and the cable 2/0, then two 1 AWG, then two 2/0 per leg.
BTQ 185-105, 105 KGF, double propeller, 12 V
The 105 kgf version, the top of the 185 mm line. The category page puts the whole BTQ 185 DP series on boats of 26 to 50 ft. The band here is the US store's own figure for this version. The manual gives a 400 A fuse at 12 V and a weight of 27.5 kg.
Its cable is two 2/0 AWG per leg for a total run under 5 m (positive plus negative), two 3/0 AWG per leg to 10 m, two 4/0 AWG per leg to 20 m. The tunnel sits at least three quarters of its diameter below the waterline. Once a year the unit comes apart for inspection, anode included.
Quick announced a brushless QSY range in September 2026, rated for ten minutes' continuous running. The QSY range will sit beside this brushed line.
Videos
One of Quick’s own videos, from its YouTube channel: the current tunnel range. It is the maker’s pitch. Watch it for what the unit looks like and how it goes in, and take any claim back to the figures above.
Other sizes and close alternatives
These are Quick’s nearest sizes by thrust, in any of its lines.
- One size down: Quick BTQ 185, six sizes, 121 to 209 lb, $3,476 to $7,511.
- One size up: Quick BTQ 250, four sizes, 265 to 529 lb, $8,624 to $10,571.
These are other makers’ units of the same style, for the same end, within a quarter of its published thrust. Each is that maker’s nearest match.
- Max Power CT100, 231 lb, $2,824.
- VETUS Bow 95, two sizes, 210 to 231 lb, $3,901.
- Sleipner E100/185T, 220 lb, $6,885.
Every model with a page here is listed, maker by maker, on the thruster index.