Boat Thruster Guide

What to buy, what it costs, what it takes to fit

We may earn a referral commission from some links on this page. It doesn't change your price or our recommendations.

Thruster specs

VETUS Bow Pro 651: specs, price and the boats it fits

The Bow Pro 651 is the 12 V BOW PRO for cruisers of about 27 to 40 ft, giving 143 lb of push with smooth variable-speed control. It’s a good fit for owners who want proportional control without moving to a 24 V or 48 V system.

Fisheries Supply has it at $3,782. It mounts in the larger mid-size tube, and that tube plus a control panel, a main switch and fuses add about $533 to $1,358. Give it its own battery close to the bow; battery, cable and charging come to roughly $1,171 to $1,247 on our estimate. See the parts list below.

Unlike the push-button Bow 60 and Bow 75 that share its tube size, it runs up to 10 minutes at a stretch and has no brushes to replace. VETUS adds that how long it runs really depends on the battery. Swap the zinc yearly and have a VETUS dealer do the servicing.

Fitting it yourself? The installer section has every spec, and the VETUS thruster review sets this model against the rest of the VETUS range.

Where this summary comes from (5 sources, read 12 October 2026)

Key facts

  • DIY level 2 of 5 Wiring prep only
  • Thrust 143 lb 65 kgf, VETUS's rating
  • Boat length 27 to 40 ft VETUS's own range
  • Price $3,782 equipment only, fisheriessupply.com, 30 August 2026
  • Fitted by a yard $11,226 to $13,837 Our estimate at 35 ft, unit and job
  • Voltage 12 V As sold
  • Mounts Tunnel Fixed mount, bow
  • To fit it Haul-out The boat comes out of the water
  • Run limit 10 min At a stretch, the user manual's S2 rating

Every figure here is the maker’s or a dealer’s, except the fitted cost, which is our estimate. The full spec sheet is further down.

How much of the install is yours

DIY 2 of 5: Wiring prep only. The yard fits the unit and does the hull work; you do the wiring prep.

DIY levels

  • Level 5: Owner install. No yard, no electrician.
  • Level 4: You fit it, electrician connects. You mount and wire it; a marine electrician makes the final connections.
  • Level 3: Split with the yard. The yard does the below-waterline part; you do the wiring.
  • Level 2: Wiring prep only. The yard fits the unit and does the hull work; you do the wiring prep.
  • Level 1: Yard job. A qualified professional does all of it.

You Yard Electrician. The bar is labor hours; a haul-out is a note.

How we rate DIY

You: 4 to 16 h Yard: 32 to 70 h Electrician: 2 to 4 h Plus a haul-out.

  1. Cut, bond and fair the tunnel; fit the gear leg, motor and propeller Yard 32 to 70 h The low end is two crew over two days, the job as owners describe it on the forums. The high end rises with boat length between two real billed figures: 32 hours at 35 ft, and the largest invoice we hold, 70 hours at 47 ft.
  2. Mount the battery box, switch and fuse holder; run and secure the cables You 4 to 16 h Our estimate. No maker times this step, and a first-time owner is slower than a yard, so the range is wide.
  3. Final connections at the battery and the motor, load test Electrician 2 to 4 h Our estimate. Nobody publishes a time for the final connections and test on their own.

Your part needs:Heavy battery cableCrimping big lugs

A qualified marine electrician should make the final connections and test them before first use. Hours are labor only.

Is it right for your boat?

What VETUS says 27 to 40 ft The maker's own range, from its listing
What our sizing says 30 to 44 ft Full thrust in 15 knots. The longest boat of each kind is in the table.

Our figure is the longest boat one unit can steer in a 15 knot wind. It is a range because each kind of boat catches the wind differently. Here a houseboat gets full thrust to 30 ft, and a catamaran to 44 ft. The maker gives one range for every boat.

The table below tries the VETUS Bow Pro 651 on each kind of boat, at every length that kind of boat is built in. The wind is 15 knots and the rules are the finder’s own. A length counts as a fit when the unit gives the thrust that boat needs at the bow and the maker lists it for that length.

A boat up to 10 percent past the maker’s range still counts here, as it does in the finder. So the table runs up to 44 ft, just past VETUS’s own range (27 to 40 ft).

The VETUS Bow Pro 651 against each kind of boat, in a 15 knot wind. Our sizing, from the finder’s own rules.
Boat Full thrust at 15 knotsStill a fit, in lighter wind
Pontoon & tritoon Not listed. A pontoon has no hull body between the logs to bore a tunnel through, and nobody sells one for these boats.
Sailboat 34 to 40 ft 41 to 44 ftfull thrust to about 14 knots at 44 ft
Houseboat 30 ft only 31 to 44 ftfull thrust to about 10 knots at 44 ft
Catamaran 39 to 44 ft None
Trawler 34 to 40 ft 41 to 44 ftfull thrust to about 14 knots at 44 ft
Motor yacht 35 to 40 ft 41 to 44 ftfull thrust to about 14 knots at 44 ft
Bass & flats Not listed. Nobody sells a tunnel kit for these hulls, and a bass boat’s shallow planing bow has almost no depth to hold one.
Wake & ski boats Not listed. Nobody sells a tunnel kit for these hulls.
Express cruiser 43 to 44 ft None
Center console No length. More thrust than the boat needs.

Reading the two length columns. The first column is where one unit gives all the thrust the boat needs in 15 knots. The second is where the finder still lists it: the unit falls short of what the boat needs by no more than 10 percent, and gives the whole figure only in the lighter wind named. On a boat shorter than the first column’s shortest length, the unit is more than the boat needs.

It is sized for six kinds of boat here. For your own boat, the finder gives an answer that also counts your drive and who does the fitting. The compare page sets this unit beside others.

What it costs fitted

These totals are our estimate of a yard job: the unit’s price, plus a yard’s hours at $160 to $180 an hour, plus the batteries, cable and charger, plus the other parts the box does not hold. A Lifting the boat out of the water on a travel lift or a trailer so work can be done below the waterline. It is billed separately from the job itself. adds $540 to $2,120 at these lengths, with 5 to 7 days out of the water, worked from eight yards’ own rate cards. The hours come from what owners and yards report. Your own yard will have its own opinion. The cost page builds the same figures line by line.

The VETUS Bow Pro 651 fitted by a yard, from the shortest to the longest boat it is sized for. Our estimate.
Boat length The unit Yard labor Haul-out Batteries, cable, charger Other parts Total
30 ft $3,782 $5,120 to $5,760about 32 hours $540 to $1,450 $1,171 to $1,247 $533 to $1,358 $11,146 to $13,597
35 ft $3,782 $5,120 to $5,760about 32 hours $620 to $1,690 $1,171 to $1,247 $533 to $1,358 $11,226 to $13,837
44 ft $3,782 $5,120 to $10,98032 to 61 hours $790 to $2,120 $1,171 to $1,247 $533 to $1,358 $11,396 to $19,487

How the batteries, cable and charger add up. We price a battery bank close to the thruster, as the makers recommend, with 10 to 20 ft of cable out and back: red for the positive, black for the negative, cut to length. The low end is the cheapest battery that meets the figure and the shorter run; the high end is a sealed (AGM) battery and the longer run. The charger is a NOCO GEN5X2 two-bank shore charger.

Batteries and lugs are priced at Fisheries Supply and the cable and charger at Defender, read 12 October 2026.

  • At 12 V: one 12 V battery, at least 170 Ah (VETUS’s minimum), $930 for the battery; VETUS’s cable table gives 1/0 AWG: $95 to $171 for the red and black cable and the lugs; a GEN5X2 charger, $146.

The sizing and the costs on this page are estimates, for guidance only and without warranty. They are no quote, and nobody has inspected your boat. Check them against the maker’s manual and your yard before you rely on them. Terms of use.

What else you buy

What follows comes from VETUS’s BOW55D installation manual 020522.11 r08 and the BOW PRO Boosted manual 020808.04 r09, May 2026 and February 2026, read 30 September 2026.

In the box
The unit assembled or in parts, the zinc anode, insulated gaskets, the drill template, the solenoid switches and the 5 A control fuse on the motor. BOW PRO: the thruster fuse in the connection unit.
Bought separately
The tunnel, the main switch (BATSW250 or BATSW600), the main fuse (ZE) and holder (ZEHC100), the cable, the control panel and its cable.
Charging
Every VETUS manual wants "its own separate battery or batteries" near the thruster, sealed if it shares the motor's compartment. The BOW PRO Boosted units carry a charger (12 V, 80 A) fed from the boat's bank, with a fused feed cable. The other manuals show an alternator and a battery separator on the wiring diagram and say nothing more.

The manual’s words, page 22 of the Boosted manual: “By connecting the 24 Volt battery bank to the MCVB boosted charge connection, the 48 Volt, battery bank is charged. An additional charging facility is not required.”

The “other parts” line in the estimate above is the priced parts below, $533 to $1,358 at Fisheries Supply’s prices on 30 September 2026. The batteries, cable and charger have a line of their own.

Parts the VETUS Bow Pro 651’s box leaves to you, from the makers’ manuals read 30 September 2026. “What to ask for” is VETUS’s own part or model where its manual names one, otherwise the dealer’s item.
Part What it is What to ask for Dealer price
Tunnel tube The fiberglass, aluminum or steel pipe the thruster sits in, bonded through the bow. BP185G10, BP185G15 (40 in, 60 in) $205–$554185 mm fiberglass tunnel tubes up to 60 in (1.5 m) long (VETUS, Sleipner Side-Power, Lewmar), at Fisheries Supply, read 16 October 2026.
Control panel The buttons or joystick at the helm. One helm, one panel: a second steering station needs a panel of its own. BPSE2 push buttons, BPJSTA joystick, BPJE2 or EZDOCK2 $219–$374Side-Power touch panel and single joystick, VETUS push-button panel, Lewmar single joystick, at Fisheries Supply.
Control cable, panel to motor The thin cable from the helm to the motor. Sold by length. VETUS panel cable, by length $29–$173Side-Power control cables, VETUS panel cables, Lewmar Gen 2 connecting cables, at Fisheries Supply.
Main fuse A slow-blow fuse of the ANL type at the battery, in the size the maker prints for the model. ZE series slow-blow, the rating in the yard table below $18–$57Side-Power ANL fuses, Blue Sea ANL fuses, at Fisheries Supply, read 16 October 2026.
Fuse holder The block the ANL fuse bolts into, with a cover. ZEHC100 $27–$93Egis and Blue Sea ANL fuse blocks, Side-Power ANL fuse holders, at Fisheries Supply, read 16 October 2026.
Main battery switch The switch that cuts the thruster off from its battery when you leave the boat. BATSW250 (BATSW600 on the bigger units), or BPMAIN12/24 for a remote switch $35–$107Egis m-Series 300 A, Blue Sea e-Series 350 A and HD-Series 600 A on/off switches, at Fisheries Supply, read 16 October 2026.
Battery cable and lugs The two heavy cables from the battery to the motor, sized to the length of the run. The wiring calculator sizes them. VETUS names none In the electrical line
Battery bank A cranking-type bank near the motor, sized by the maker's cold cranking amps. The battery calculator checks it. VETUS names none In the electrical line
Charger or charge feed How the thruster bank gets charged: a shore charger of its own, a DC-to-DC charger or charging relay from the boat's system, or a charger built into the unit. VETUS names none $146–$305NOCO GEN5X2 shore charger, Victron Orion-Tr Smart DC-DC charger, Blue Sea ML-ACR charging relay, at Fisheries Supply.
Glass, resin, filler and sealant What bonds the tube or housing into the hull and seals the gear leg. VETUS names none Not priced

The cost page has the whole list with what every maker says about each part.

For the yard and the installer

The full spec sheet, grouped the way a yard reads it. Every figure is the maker’s or a dealer’s, with its source.

The VETUS Bow Pro 651, every published figure the site holds, with where each came from.
Thrust and motor
Thrust 143 lb (65 kgf) As printed: Rated thrust: 650 N (65 kgf, 143 lbf) (VETUS Owner's Manual 020810.01)
Motor2.7 kW
Voltage12 V
Fitting
TypeTunnel, fixed mount
End of the boatBow
Tunnel diameter185 mm
What it does to the hullTunnel bore below the waterline
Haul-out to fit itYes
Maker’s boat length27 to 40 ft
Price and ordering
Price $3,782 equipment only, a dealer's price, fisheriessupply.com, 30 August 2026
Part number BOWA065112 V
Documents
Manual Installation manual (PDF)on the maker's site
Warranty VETUS gives 3 years, or 1 for professional use, and it transfers to the next owner. Claims go through the dealer only. It is void unless an authorized VETUS dealer does the periodic maintenance, and transport, labor and lifting are excluded. VETUS's warranty policy
The site’s reviewVETUS thruster review

Draw, cable, fuse and battery, at each voltage

These are the maker’s own figures, at each voltage it is sold at. The cable is the size for the shortest run in the maker’s table. A longer run may need heavier cable, and the wiring calculator works that out for your own boat.

The VETUS Bow Pro 651’s draw, cable, fuse, battery and run limit, as the maker publishes them.
Voltage Draw Maker’s cable Fuse Battery Run limit
12 V 237 Anominal draw 1/0 AWG for up to 20 ft of cable counted out and back. Longer runs take heavier cableinstallation manual 020806.08, r08, December 2025 300 A, and 250 A (ZE250) in the controllerinstallation manual 020806.08, r08, December 2025 1 x 170 Ah - 12 V, in amp-hoursVETUS installation manual 020806.08, r08, December 2025 10 min at a stretch, the user manual's S2 ratingBOW PRO user manual

What to weigh

Each point names the fact it rests on.

What to weigh

  • The boat comes out of the water to fit it: it needs a tunnel bore below the waterline.The mounting: a bore through the hull, or a housing recessed into it

What the manual and listings say

This is the note we keep on the VETUS Bow Pro 651, written from the maker’s manual, its product pages and the dealer’s listing.

In the box: Proportional: the joystick sets how hard it pushes. The thruster fuse sits in the connection unit.

Our note

A 12 V unit in a 185 mm tunnel. It is brushless and proportional, so the joystick sets how hard it pushes instead of switching it on and off. The installation manual rates it at 10 minutes (S2). The user manual says run time is mainly limited by the battery. The US press release's "unlimited runtime" appears in neither.

The manual gives 237 A at 12 V (271 at 10.5) and an example battery of one 170 Ah 12 V battery. It calls for a 300 A main fuse and a 250 A fuse in the controller that must stay in place. It gives 1 AWG cable to 20.7 ft of total run. The manual gives it a 2.7 kW motor.

Fisheries Supply's listing printed 3.1, the 48 V BOWA0764's motor. The row carries the manual's figure. The June 2026 user manual cut its slow-blow fuse from 300 A to 250. The warranty runs three years and is claimed through the dealer only. It is void unless an authorized VETUS dealer does the periodic maintenance, and labor, transport and lifting are excluded.

Videos

Two of VETUS’s own videos, from its YouTube channel: the BOW PRO range in short, and the full BOW PRO electrical and mechanical install. They are the maker’s pitch. Watch them for what the unit looks like and how it goes in, and take any claim back to the figures above.

VETUS’s own video, on VETUS’s YouTube channel. The picture is a still from it.
VETUS’s own video, on VETUS’s YouTube channel. The picture is a still from it.

Other sizes and close alternatives

These are VETUS’s next sizes in the same line, by thrust.

These are other makers’ units of the same style, for the same end, within a quarter of its published thrust. Each is that maker’s nearest match.

Compare them side by side

Every model with a page here is listed, maker by maker, on the thruster index.

Where to go next

The specs are the maker’s and the dealers’, on the dates shown. The sizing and the costs are our arithmetic, done without seeing your boat.