We may earn a referral commission from some links on this page. It doesn't change your price or our recommendations.
Discontinued thruster
Sleipner SRVP130 PRO (discontinued): specs, manual and parts
The Sleipner SRVP130 PRO is a retractable thruster. It drops out of the hull when you use it and folds back up after. Sleipner has discontinued it. Its own product page said so when we read it on 11 October 2026.
This page stays up for the owners still running one. It holds the published figures, the part numbers and the manual. You will not find the unit in the thruster finder, the tool here that matches a unit to your boat, or on the compare page. If you need a new thruster, start with either of those.
The published figures
| Type | Retractable, drops down |
|---|---|
| Thrust | 353 lb (160 kgf) |
| As the maker printed it | Thrust at 24V: 160kg / 353lbs; Thrust at 21V: 130kg / 287lbs |
| Voltage | 24 V |
| Tunnel diameter | 250 mm |
| Maker’s boat length | 43 to 62 ft |
| Part number | SRVP130/250T-24V24V |
| Last price we read | No price held |
| Manual | Sleipner’s manual for it |
Service parts
These are Sleipner’s own part numbers for the parts an owner replaces, where we could find them: the pin that drives the propeller, the propeller, the anode, the brushes, the switch gear, the fuse and the motor. We read them on 11 October 2026. The last column says how we know each one fits this model. Give the dealer your thruster’s serial number from its label when you order.
| Part | Part number | Sleipner’s name for it | How we know it fits |
|---|---|---|---|
| Drive pin (the pin that drives the propeller) | 9 1241 | Drive pin propeller SE120-300 | Sleipner’s parts page lists this model |
| Propeller, right hand | 10 1271 RH | Propeller, Q-Prop Ø250mm RH | Sleipner’s parts page lists this model |
| Anode | 20 1180 A | Anode kit (Al-Zn-In), for 215/300 mm gear legs | Sleipner’s parts page lists this model |
| Motor brush kit | BRUSH-09K | Brush kit SP125 + SE130 24V | By the part’s name only. Confirm with your serial number.Sleipner asks for the thruster’s serial number with every brush kit order. |
| Solenoid (the motor switch) | 41371243 | Solenoid SE80/100/120/130/150/170 24V | Sleipner’s parts page lists this model |
| Solenoid kit | 9 0132 24 | Solenoid kit SEP130 24V | Sleipner’s parts page lists this model |
| Main fuse | ANL 325 | Recommended fuse A | Sleipner’s page for this modelThe rating on Sleipner’s page for this model. The fuse holder is SMANLHOLD. |
| Retract control unit | 150000 | Electronic Control Unit SRV | Sleipner’s parts page lists this model |
| Position sensor | 140144 | Position sensor 5KOhm 3pin | Sleipner’s parts page lists this model |
| Lift actuator | 139999-P8 | Actuator P8, 24V SRV | Sleipner’s parts page lists this model |
| Tunnel anode rod | 140629 | Anode rod for SRV thrusters | Sleipner’s parts page lists this model |
| Replacement motor | 9 0104 24 | 24V (SEP/SR/SRP130) | Sleipner’s parts page lists this model |
What the manual and listings say
A retractable: it drops straight down out of a housing in the hull when used and lifts back up after. It goes in through a large opening below the waterline, a bigger yard job than a tunnel. PRO means proportional: the joystick sets how hard it pushes. Twin propellers in a 250 mm tunnel, for boats of about 43 to 62 ft.
Sleipner rates it 160 kg (353 lb) at 24 V and 130 kg (287 lb) at 21 V. Sleipner's own page names the ERV130 eVision as its replacement.
Replacement and close alternatives
The replacement: Sleipner ERV130 eVision 24V. Sleipner’s own page for this model links it as the replacement.
These are Sleipner’s nearest current sizes by thrust, in any of its lines.
- Nearest below: Sleipner SRVP100 PRO, 256 lb, $13,070.
- Nearest above: Sleipner ERV170 eVision, 375 lb, $26,455.
Other makers’ current units of the same style, for the same end, within a quarter of its published thrust:
- Lewmar 250VRTT Vertical Retractable, 353 lb, $29,417.