We may earn a referral commission from some links on this page. It doesn't change your price or our recommendations.
Thruster specs
Quick BTQ 110: specs, price and the boats it fits
The BTQ 110 is Quick’s smallest bow thruster, a neat way to make docking easier on a small cruiser or day boat of about 16 to 25 ft. It sits in a short tube through the hull near the bow and gives about 55 lb of sideways push on 12 V. Quick has built thrusters since 2007, and builders such as Beneteau and Jeanneau fit its units at the factory.
Quick’s US store sells it for $2,184, for the thruster alone. The box holds the thruster, a drilling template and a seal, so see below for the rest. The main extras are a control panel ($465 for Quick’s push-button model), the tube, a fuse and holder, and a battery with its cable and charger, about $1,224 to $1,315 more.
On Quick’s older units the motor brushes are what wear, and Quick asks for a strip-down once a year with a fresh zinc. Quick says plainly that the thruster isn’t meant to run nonstop. Hold it on for roughly 5 minutes 40 seconds and the panel shuts it off for 20 minutes to cool. The US warranty is three years, as long as service is done by someone Quick has authorized.
Fitting it yourself? The installer section has every spec, and the Quick thruster review sets this model against the rest of the Quick range.
Where this summary comes from (9 sources, read 11 October 2026)
- Quick USA store product page
- Boating Industry Canada, 18 May 2023: Quick thruster production began in 2007
- Quick BTQ Series installation manual, REV005A (July 2025)
- Quick TCD 2022/2042 control panel manual, REV001a
- Quick USA store: thrusters, panels, tubes, fuses and spares
- Quick USA: conditions of warranty
- myHanse, Jul 2016: brushes, relay and a six-month parts wait
- myHanse, Aug 2016: thruster stops after hard use in a crosswind
- myHanse, Jun 2022: Quick stern thruster, brushes and the overheat lockout
Key facts
- DIY level 1 of 5 Yard job
- Thrust 55 lb 25 kgf, Quick's rating
- Boat length 16 to 25 ft Quick's own range
- Price $2,184 equipment only, quickusastore.com, 12 October 2026
- Fitted by a yard $9,405 to $11,392 Our estimate at 25 ft, unit and job
- Voltage 12 V As sold
- Mounts Tunnel Fixed mount, bow
- To fit it Haul-out The boat comes out of the water
- Run limit Not published Quick prints none for the motor. Its control panel cuts the command after about five minutes
Every figure here is the maker’s or a dealer’s, except the fitted cost, which is our estimate. The full spec sheet is further down.
How much of the install is yours
DIY levels
- Level 5: Owner install. No yard, no electrician.
- Level 4: You fit it, electrician connects. You mount and wire it; a marine electrician makes the final connections.
- Level 3: Split with the yard. The yard does the below-waterline part; you do the wiring.
- Level 2: Wiring prep only. The yard fits the unit and does the hull work; you do the wiring prep.
- Level 1: Yard job. A qualified professional does all of it.
You Yard Electrician. The bar is labor hours; a haul-out is a note.
How we rate DIYYou: none Yard: 32 to 70 h Electrician: in the yard’s hours Plus a haul-out.
- The whole job: hull, unit and wiring Yard 32 to 70 h The low end is two crew over two days, the job as owners describe it on the forums. The high end rises with boat length between two real billed figures: 32 hours at 35 ft, and the largest invoice we hold, 70 hours at 47 ft.
Quick’s manual: “Installation and subsequent inspection or repair work must only be carried out by qualified personnel.” The manual.
Hours are labor only.
Is it right for your boat?
Our figure is the longest boat one unit can steer in a 15 knot wind. It is a range because each kind of boat catches the wind differently. Here a sailboat gets full thrust to 25 ft, and an express cruiser to 27 ft. The maker gives one range for every boat.
The table below tries the Quick BTQ 110 on each kind of boat, at every length that kind of boat is built in. The wind is 15 knots and the rules are the finder’s own. A length counts as a fit when the unit gives the thrust that boat needs at the bow and the maker lists it for that length.
A boat up to 10 percent past the maker’s range still counts here, as it does in the finder. So the table runs up to 27 ft, just past Quick’s own range (16 to 25 ft).
| Boat | Full thrust at 15 knots | Still a fit, in lighter wind |
|---|---|---|
| Pontoon & tritoon | Not listed. A pontoon has no hull body between the logs to bore a tunnel through, and nobody sells one for these boats. | |
| Sailboat | 21 to 25 ft | 26 to 27 ftfull thrust to about 14 knots at 27 ft |
| Houseboat | No length. Short of the thrust the boat needs. | |
| Catamaran | No length. Outside the maker's length range. | |
| Trawler | 23 to 25 ft | 26 to 27 ftfull thrust to about 14 knots at 27 ft |
| Motor yacht | No length. Outside the maker's length range. | |
| Bass & flats | Not listed. Nobody sells a tunnel kit for these hulls, and a bass boat’s shallow planing bow has almost no depth to hold one. | |
| Wake & ski boats | Not listed. Nobody sells a tunnel kit for these hulls. | |
| Express cruiser | 27 ft only | None |
| Center console | No length. More thrust than the boat needs. | |
Reading the two length columns. The first column is where one unit gives all the thrust the boat needs in 15 knots. The second is where the finder still lists it: the unit falls short of what the boat needs by no more than 10 percent, and gives the whole figure only in the lighter wind named. On a boat shorter than the first column’s shortest length, the unit is more than the boat needs.
It is sized for three kinds of boat here. For your own boat, the finder gives an answer that also counts your drive and who does the fitting. The compare page sets this unit beside others.
What it costs fitted
These totals are our estimate of a yard job: the unit’s price, plus a yard’s hours at $160 to $180 an hour, plus the batteries, cable and charger, plus the other parts the box does not hold. A Lifting the boat out of the water on a travel lift or a trailer so work can be done below the waterline. It is billed separately from the job itself. adds $370 to $1,300 at these lengths, with 5 to 7 days out of the water, worked from eight yards’ own rate cards. The hours come from what owners and yards report. Your own yard will have its own opinion. The cost page builds the same figures line by line.
| Boat length | The unit | Yard labor | Haul-out | Batteries, cable, charger | Other parts | Total |
|---|---|---|---|---|---|---|
| 21 ft | $2,184 | $5,120 to $5,760about 32 hours | $370 to $1,010 | $1,224 to $1,315 | $427 to $923 | $9,325 to $11,192 |
| 25 ft | $2,184 | $5,120 to $5,760about 32 hours | $450 to $1,210 | $1,224 to $1,315 | $427 to $923 | $9,405 to $11,392 |
| 27 ft | $2,184 | $5,120 to $5,760about 32 hours | $480 to $1,300 | $1,224 to $1,315 | $427 to $923 | $9,435 to $11,482 |
How the batteries, cable and charger add up. We price a battery bank close to the thruster, as the makers recommend, with 10 to 20 ft of cable out and back: red for the positive, black for the negative, cut to length. The low end is the cheapest battery that meets the figure and the shorter run; the high end is a sealed (AGM) battery and the longer run. The charger is a NOCO GEN5X2 two-bank shore charger.
Batteries and lugs are priced at Fisheries Supply and the cable and charger at Defender, read 12 October 2026.
- At 12 V: one 12 V battery, at least 450 CCA and 115 Ah (Quick’s minimum), $998 for the battery; Quick’s cable table gives 1 to 1/0 AWG: $80 to $171 for the red and black cable and the lugs; a GEN5X2 charger, $146.
The sizing and the costs on this page are estimates, for guidance only and without warranty. They are no quote, and nobody has inspected your boat. Check them against the maker’s manual and your yard before you rely on them. Terms of use.
What else you buy
What follows comes from Quick’s BTQ Series installation manual REV 005A and the TCD control manual, September 2025, read 30 September 2026.
- In the box
- The thruster with its reversing contactor and anode, a drilling template, gasket, O-ring, the manual.
- Bought separately
- "Recommended Quick accessories not included": the TCD control panels, the line switch, the THF fuse holder. Plus the fuse, the cable, a battery disconnection switch, a 4 A control fuse and switch, the tube.
- Charging
- The manual gives a battery table by model, in amp-hours and cold cranking amps, and a diagram with the panel on the service battery. It says nothing about how the thruster bank is charged.
The manual’s words, page 10: “Standard supply and material included in the package: Thruster, Drilling template, Gasket, O-ring, Installation and use manual, Conditions of warranty.”
The “other parts” line in the estimate above is the priced parts below, $427 to $923 at Fisheries Supply’s prices on 30 September 2026. The batteries, cable and charger have a line of their own.
| Part | What it is | What to ask for | Dealer price |
|---|---|---|---|
| Tunnel tube | The fiberglass, aluminum or steel pipe the thruster sits in, bonded through the bow. | Quick names none | $90–$108110 mm fiberglass tunnel tubes up to 60 in (1.5 m) long (VETUS), at Fisheries Supply, read 16 October 2026. |
| Control panel | The buttons or joystick at the helm. One helm, one panel: a second steering station needs a panel of its own. | TCD 2022, 2042, 2044 or 2062 | $219–$374Side-Power touch panel and single joystick, VETUS push-button panel, Lewmar single joystick, at Fisheries Supply. |
| Control cable, panel to motor | The thin cable from the helm to the motor. Sold by length. | Quick names none | $29–$173Side-Power control cables, VETUS panel cables, Lewmar Gen 2 connecting cables, at Fisheries Supply. |
| Main fuse | A slow-blow fuse of the ANL type at the battery, in the size the maker prints for the model. | CNL DIN fuse, the rating in the manual | $18–$57Side-Power ANL fuses, Blue Sea ANL fuses, at Fisheries Supply, read 16 October 2026. |
| Fuse holder | The block the ANL fuse bolts into, with a cover. | THF3 to THF6 | $27–$93Egis and Blue Sea ANL fuse blocks, Side-Power ANL fuse holders, at Fisheries Supply, read 16 October 2026. |
| Main battery switch | The switch that cuts the thruster off from its battery when you leave the boat. | TSC 2000 or TMS line switch, or a battery switch | $35–$107Egis m-Series 300 A, Blue Sea e-Series 350 A and HD-Series 600 A on/off switches, at Fisheries Supply, read 16 October 2026. |
| Control-circuit fuse and switch | A small fuse, and often a switch, on the thin wire that powers the panel or control box. | A 4 A fast-blow fuse and a switch | $8–$12Blue Sea in-line ATO fuse holders, at Fisheries Supply, read 16 October 2026. |
| Battery cable and lugs | The two heavy cables from the battery to the motor, sized to the length of the run. The wiring calculator sizes them. | Quick names none | In the electrical line |
| Battery bank | A cranking-type bank near the motor, sized by the maker's cold cranking amps. The battery calculator checks it. | Quick names none | In the electrical line |
| Charger or charge feed | How the thruster bank gets charged: a shore charger of its own, a DC-to-DC charger or charging relay from the boat's system, or a charger built into the unit. | Quick names none | $146–$305NOCO GEN5X2 shore charger, Victron Orion-Tr Smart DC-DC charger, Blue Sea ML-ACR charging relay, at Fisheries Supply. |
| Glass, resin, filler and sealant | What bonds the tube or housing into the hull and seals the gear leg. | Quick names none | Not priced |
The cost page has the whole list with what every maker says about each part.
For the yard and the installer
The full spec sheet, grouped the way a yard reads it. Every figure is the maker’s or a dealer’s, with its source.
| Thrust and motor | |
|---|---|
| Thrust | 55 lb (25 kgf) As printed: 25 Kgf (55.1 lb) |
| Motor | 1.3 kW |
| Voltage | 12 V |
| Fitting | |
| Type | Tunnel, fixed mount |
| End of the boat | Bow |
| Tunnel diameter | 110 mm |
| What it does to the hull | Tunnel bore below the waterline |
| Haul-out to fit it | Yes |
| Maker’s boat length | 16 to 25 ft |
| The tunnel | |
| Tunnel length | The optimal length is three to four times the tube diameter. A ratio of up to six can be tolerated. Longer tubes lose more of the thrust to friction. Quick’s installation manual |
| Depth below the waterline | In the bow and as low as possible, at least 0.75 times the tunnel diameter below the waterline, to avoid cavitation at the propeller. BTQ250 and BTQ300 installation manual, REV006C |
| Price and ordering | |
| Price | $2,184 equipment only, the maker's own price, quickusastore.com, 12 October 2026 |
| Part number | FGBT11025120T0025 KGF, 12 V |
| Documents | |
| Manual | Installation manual (PDF)on the maker's site |
| Warranty | Quick gives at least 3 years from purchase, with repair or replacement at Quick's discretion. It is void if maintenance is done by anyone Quick has not authorized, or with parts that are not original. Removal and refitting are at your cost. Quick USA's conditions of warranty |
| The site’s review | Quick thruster review |
What to weigh
Each point names the fact it rests on.
What to weigh
- The boat comes out of the water to fit it: it needs a tunnel bore below the waterline.The mounting: a bore through the hull, or a housing recessed into it
What the manual and listings say
This is the note we keep on the Quick BTQ 110, written from the maker’s manual, its product pages and the dealer’s listing.
In the box: The thruster, a drilling template, gasket and O-ring. The TCD panel and the fuse holder are bought.
Our note
The smallest Quick, single propeller in a 110 mm tunnel. Quick is the brand Beneteau, Jeanneau and Hanse fit at the factory, so most owners meet it without having chosen it. The manual gives a 130 A fuse and a weight of 9.3 kg. Its cable is 2 AWG for a total run under 5 m (positive plus negative), 1 AWG to 10 m, 2/0 to 20 m.
The manual prints a fuse and cable sizes but no current draw and no battery figure. No product page gives a run time. The installation manual says the unit is not designed for continuous use and leaves the limit to the control panel. The panel's own manual cuts the command after about five minutes and resets it after a cool-down the panel computes.
The tunnel sits at least three quarters of its diameter below the waterline. Once a year the unit comes apart for inspection, anode included. The warranty runs three years from purchase, with repair or replacement at Quick's discretion. The warranty is void for maintenance by anyone Quick has not authorized or for non-original parts. Removal and refitting are at your cost. The price is Quick's US store's own for this size at 12 V, read 12 October.
Videos
One of Quick’s own videos, from its YouTube channel: the current tunnel range. It is the maker’s pitch. Watch it for what the unit looks like and how it goes in, and take any claim back to the figures above.
Other sizes and close alternatives
These are Quick’s next sizes in the same line, by thrust.
- One size up: Quick BTQ 125, two sizes, 66 to 88 lb, $2,511 to $2,754.
These are other makers’ units of the same style, for the same end, within a quarter of its published thrust. Each is that maker’s nearest match.
- VETUS Bow 25, 55 lb, $1,619.
- Lewmar 110TT Thruster Kit, 62 lb, $936.
- Sleipner SE25/110S, 66 lb, $1,485.
Every model with a page here is listed, maker by maker, on the thruster index.